UPVC Replacement Door Handles
The handles on your doors wear out over time and need to be replaced. When doing this it is crucial that the new handles conform to the exact dimensions of the previous handle.
The top screw's location, the lever and the keyhole sizes are the three measurements you have to verify. Check the size guide for assistance in this.
Inline Lever/Lever
A lever door handle is a contemporary handle that can be used on new or replacement doors. This type of handle is available in various styles and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The uPVC/Composite door handles are made of robust materials and are ideal for multi point lock doors that require a heavy duty design. The handles are inline, and use the same screws and spindle to fix them. They are easily fitted on a new or existing uPVC/Composite door.
The design of the sprung lever allows the handle to be positioned and angled to provide a comfortable grip and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles. This helps to ensure that the finish is of high quality and performance will last for a long time. The sprung lever can also be reduced to accommodate more locks. This is particularly useful for narrower door frames where the cylinder is located further back. A lever that is shorter can be used for doors with latches that can be opened by the thumb located on the inside.
Lever Pad
A Lever Pad door handle made of upvc operates differently than lever handles found on most doors. These handle types can either work off one single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are generally used on UPVC double-glazed doors and come in a variety of styles and styles.
The handles are available in various finishes, including White chrome and Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.
All of the UPVC lever pad styles for handles come with the spindle and screws that allow them to be put on a new or existing uPVC door. upvc door handle replacement chichester repairmywindowsanddoors.co.uk fixing centres of 211mm allow for a wider size handle that can often be a benefit when replacing a faulty or worn multi point door lock mechanism. The handle levers are spring-loaded, which solves the issue of handles hanging out of the horizontal position when they are not in use.
It is essential to ensure that the dimensions of the PZ for both the multipoint lock as well as the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement may also be called 'handle centre or cylinder centre'. It is important to match the right handles.
Once you have the proper PZ size, you'll need to ensure that the handle lever pads and push pads are in a suitable shape for the American with Disabilities Act (ADA) compliant handles that you need for your doors. These are typically rectangular or round in shape, with an internal lever and an external push pad.
Most of the UPVC lever pads we offer are sprung, which means that they return to their horizontal position after not in use, instead of hanging out and possibly securing in the frame. This prevents drafts and cold air from entering a property. Also, the majority of the UPVC handle lever pad style handles are swivel, allowing you to install them on either side of the door.
Euro Cylinder
Cylinder locks are usually found on uPVC doors, but can also be used on other types of doors. The cylinder lock is operated by using a key that unlocks the cylinder's casing. The case is then able to reveal pins that can be aligned to the pins in the lock and allow them to turn the camera that rotates, opening the door. Euro cylinders can be fitted with up to six pins. External and internal doors require different levels of security.
The choice of cylinder is crucial. It depends on the use that your doors and handles will receive. For instance, exterior doors must be secured with a higher security cylinder, while internal doors can be secured with the standard cylinder. Additionally, certain cylinders are available with extra features that can improve security even more, like anti-drill or anti-bump properties.
A euro cylinder needs to be properly measured to ensure that it is the correct size for your door. The cylinder should be measured from the hole in the center of the fixing screw to the other end of the cylinder including the thumb turn if you have one. It is best to do this with the lock in place however when this isn't possible, you can take it off to measure. It is essential to not have a cylindrical lock that extends beyond the handle or escutcheon. This could make it vulnerable to lock snapping attacks.
The majority of modern cylinders have been designed with bump and anti-drill features built into their design. They are designed to minimize attacks by forcing cylinders to rotate in a new direction. This will help to deflect an attack and protect your door.
There are also cylinders that are made to resist snapping. This is a common attack on cylinders. A specific tool is used to break the lock's break line and then the front of the cylinder is snapped off. This is much quicker and more straightforward than opening the door with multipoint locks. It also leaves little evidence of a break-in which can impede the insurance claim.
Spring Cassette
This spring cassette is found in the base plate of your door handle. It is a spring-loaded solution to bring your multipoint lock handles to their normal position after usage. In the past, a lot of handles of this kind did not have a spring integrated into them, and as a result, they are more likely to slide or 'drop' once the locking mechanism is disengaged. This simple part is the best solution to address this issue. It also prevents your door from becoming stuck in the closed or open position since they are difficult to close manually.
These spring cassettes were designed to be used with a spring multipoint locks. They are not compatible with handles that are not sprung and you'll have to cut a hole in your backplate for them to fit. (Please see the image for a detailed diagram). These cassettes can be used as a replacement to damaged or missing cassettes on the backplate of uPVC door handles. They are available as one unit. They feature a square cut out that is able to accommodate an 8mm shaft.
These spring cassettes are a fantastic value for money way to fix the problem of door handles that are that are sagging. These spring cassettes are easy to install and will extend the life of your uPVC door. Contact us for more information about our selection of uPVC accessories and spares. We are always happy to offer professional advice and assistance you.